Products

Hydraulic tension benefits industrial machinery

When commissioning industrial machinery, the importance of correct bearing installation is paramount. Bearing manufacturers say incorrect installation is directly the cause of 16 percent of all failures – and maintenance specialists say it is likely to be a big contributor downstream to generally shorter service life and resulting maintenance safety hazards. “When a new bearing is incorrectly mounted – be it by way of poor fitting, brute installation force, or incorrect tools – it can lead directly to premature and sometimes very swift bearing failure,” says internationally successful hydraulic tensioning tool manufacturer John Bucknell, who is Founder and CEO of Technofast. “A poorly installed bearing is not only a pending production liability in terms of service life, but also in terms of expensive downtime and the OH&S factors involved in getting the worn part out again when it fails prematurely,” he says. “Crude approaches may be quick, but they can be nasty and dangerous, risk damage to machinery shafts, and make subsequent bearing failure analysis either difficult or impossible,” says Mr Bucknell, whose safety-engineered and money-saving hydraulic tensioning solutions are used in time-critical fastening and service applications ranging from mining and quarry conveyors and comminution equipment, through to applications in conventional and nuclear power stations. Bearing sleeve withdrawal These same qualities of speed, precision and avoidance of downtime while ensuring worker safety were demonstrated in service recently with a bearing sleeve withdrawal operation when assembling a new mobile crusher and conveyor. It was being commissioned on-site to make road-base gravel for applications such as new highways and worksite infrastructure. The newly imported machine – purpose-built to be assembled where needed for immediate service – required precision technology that was demonstrably superior to old methods such as using a hand-made jig laboriously fabricated for the purpose, with no way of determining […]

RS PRO launches energy efficiency products for manufacturers

RS is again expanding its Australasian RS PRO range with the addition of products that deliver improved energy saving and efficiency. Due to the popularity of these products they are being fast-tracked to market and will launch in September. The product range is tailored to reduce energy consumption from building facilities and the production line, from solar panel solutions, smart lighting options and high-efficiency power supplies. “We’re helping our customers embrace energy efficiency with the RS Pro brand,” says Scott Philbrook, Managing Director RS ANZ. “Both production line and facilities products are part of this launch. From energy meters, power supplies and lighting right down to PPE and Tool Kits that deliver improved energy savings and efficiency are included.” Each RS PRO product is backed by the RS Seal of Approval, which represents industry standards for audit, inspection, test, and certification. This, combined with longer than average warranties reflects RS Components confidence in the quality and longevity of their products. According to Scott, the expansion in the range is meeting demand in the market for affordable options for engineers looking for a choice. “Every corner of the manufacturing environment is being pressured by energy costs and this is an opportunity for our customers to have variety in their product selection,” he explained. RS has supreme confidence in the RS PRO brand and has invested heavily in expanding these product ranges and anticipates a favourable response and uptake in both the Australian and New Zealand markets.

Hydraulink franchise owner brings strong capabilities to Milperra businesses

A man who spent six months researching the hydraulic hose, fitting and service needs of Milperra’s businesses says he is delighted to have joined a Hydraulink national team dedicated to the same values he holds. Peter Tsekenis recently became the latest member of the Hydraulink family of franchise operators, which spans more than 400 services points across Australia and New Zealand. He says Hydraulink – which trades under the market signature “Best Under Pressure” – is an ideal fit for a person such as himself with a strong mechanical background and expert understanding of the importance of safety, precision, attention to detail and a can-do attitude that starts with first understanding customers’ needs. “We have a huge diversity of industries in Milperra – all dependent upon good hydraulic service to keep mobile and plant machinery functioning reliably without wasting downtime. The robust industry base here extends from distribution, transport and major import and export logistics, through to building, construction, diesel and civil machinery, metalworking, conveying and just about everything mechanical under the sun. Milperra really is a production powerhouse – and nearly all the machinery involved uses hydraulics in one way or another. “My research told me all of these could benefit from a door-to-door maintenance and breakdown service that gives them maximum uptime. As someone experienced in the civil engineering industry, I understand that breakdowns and ‘that’ll do’ maintenance cost big money, so I want to bring excellence and quality to the table.” Researching the market “When I as doing my research, driving around Milperra and talking to business for six months, I found that a lot of local industries were going outside the district to get their service needs. “So there seems to me to be a real gap in the market here for someone operating locally within […]

Freightlancer and Loadshift merge

Leading Australian heavy haulage marketplaces Freightlancer and Loadshift today announced an official merger. Both platforms will merge under the Loadshift banner, forming Australia’s largest transport marketplace which has delivered over 125 million kilometers of freight across Australia in the last 12 months. The merger will transform Loadshift from a simple membership-based bulletin board to a full marketplace for freight, and in the process of doing so introduces a 3% (for shippers) 10% (for carriers) commission-based model for non members. “Merging our freight division into one marketplace is a significant milestone for the business. Combining the two platforms will give our carriers more opportunities to find loads, while offering shippers access to more carriers across Australia. The new platform will also provide our users with new features which will enhance the shipper and carrier experience,” said Matt Barrie, Executive Chairman at Freightlancer. For carriers, the new marketplace platform will offer more access to freight, secure payment options, shipper transparency, invoice financing powered by Butn and an internal messaging platform which will offer direct quoting. As for shippers, the new features will provide enhanced carrier reviews which will improve the vetting process and managed services offerings including freight operations and project management. “Whilst the new platform will be a new experience for members, we have still kept the core principles of connecting shippers and carriers across the country. We have, however, introduced enhancements which will improve the overall user experience and offer carriers an additional level of safety and reliability when transporting loads. The added vetting features will be crucial to ensure shippers are finding quality, reliable carriers,“ said Drew Davis, General Manager at Loadshift. Founded in 2007, Loadshift was designed to solve the issue of trucks running with empty trailers by connecting shippers and carriers around Australia. According to a recent […]

Made in Australia – Kickstarting a resilient local IT Supply Chain is critical

-Phil Straw, CEO, SoftIron The world has been through a fundamentally transformative time that has demonstrated the fragility of supply chains. Talk to anyone you know in any field, and virtually everyone is dealing with issues of a supply chain that is struggling. This is true for Australia, but also the world at large. SoftIron is a company working to bring sovereign resilience to Australia where mission-critical data infrastructure is concerned. Whether it’s transportation, food, medical facilities, or critical supplies, computers have become the critical infrastructure for virtually every industry that enables the way we live. It’s imperative that data infrastructure be readily available, regardless of geopolitical events disrupting supply chains; and governments and industry leaders operating in today’s climate must start paying more attention to this matter for their longevity. SoftIron is currently in the process of establishing a local manufacturing facility and audit centre equipped to deliver critical data infrastructure for Australia and the region at large. It will be the first-ever base-level computer manufacturing facility on Australian soil – a game-changer. We are funding this facility, in part, via a Sovereign Industrial Capability Priority Grant from the Department of Defence, complemented with an initial investment on our part of around AUS$2M. We believe we can uniquely contribute to the security of Australia’s Critical Infrastructure and Systems of National Significance in very substantive ways. We liken the current global situation to a detrimental “addiction” that had not only become practical, but unavoidable. The addiction of which I speak is the IT industry’s current reliance on cheap technology design, supply and manufacturing from foreign nations, including China. While things were great for a period of time, events like COVID-19 have sounded the alarm bells about the necessity of sovereign capability in building critical infrastructure. In the aftermath of this […]

Contactless monitoring of igus cables in e-chains

From Treotham, i.Sense CF.D sensors use high-frequency technology to detect defects in bus and data cables, preventing expensive system downtimes. Smart monitoring of igus bus and data cables goes into the next round: the latest generation of i.Sense CF.D monitoring sensors from Treotham checks the electrical condition of chainflex cables in e-chain systems – without contact and without intervention in the existing harnessing. This allows real-time monitoring without any extra cores and, in combination with the new i.Cee: plus II evaluation module, allows even more efficient predictive maintenance for protection against expensive system failures. The latest CF.D generation facilitates the entry into predictive maintenance of chainflex bus and data cables in igus e-chain systems. The smart system consists of two sensor units clipped onto the cable before and after the chainflex cable to be monitored. They are small enough to fit into the distribution box on the moving end side and into the control cabinet on the fixed end side. During operation, the sensors continuously check the cables’ transmission properties. High-frequency technology detects the smallest changes in state without contact The new generation of igus monitoring sensors from Treotham uses high-frequency technology that works without additional sacrificial cores and without contacting existing cores. “This technology allows the sensors to reliably measure even the smallest transmission deteriorations in cables and connectors,” says Richard Habering, head of the igus smart plastics business unit. “This allows effective predictive maintenance in moving industrial applications in which cables and connectors are subjected to continuous mechanical stress. The new generation of CF.D sensors is compatible with most bus and data cables in the igus chainflex cable range. “Condition monitoring enables machinery and equipment users to detect and replace cables approaching their wear limit at an early stage, significantly enhancing plant safety.” It is a small investment […]

Suhner Australia unveils new grinders with exceptional speed stability

Suhner Australia, a leader in metal finishing solutions, has released its next-generation of variable speed, 125mm Angle grinders – the Suhner UWG 11R and the UWK 11R. Both models provide unrivalled speed stability regardless of whether they are operating at 2,800rpm or 10,500rpm, to help deliver a variety of quality finishes. Specifically designed to keep vibration at bay, both grinders provide the correct speed and stability under torque, allowing the user to operate them for an extended period of time. This ensures a consistent, quality finish on stainless steel, aluminium, brass, other alloys and ferrous metals. Moreover, the Suhner UWG 11R and UWK 11R can be combined with a variety of abrasive, cutting or hook and loop discs as well as a range of non-woven and fine finish products, so that users can attain a wide variety of finishes. Made in Germany and built to last, both the UWG 11R and UWK 11R grinders are quality tools suitable for working on a range of applications including structural fabrication, balustrades, vehicle components, medical products, aircraft parts, and many other light or heavy manufacturing applications. The Suhner UWG 11R and UWK 11R variable speed grinders are ergonomic, slimline and lightweight. The UWG11 has 1100W of power, yet weighs only 2.1kg. It is ideal for fine sanding applications with fibre, hook, and loop or flap discs and then, any cutting requirements. The UWG 11R is probably the most user-friendly 125mm grinder on the market today. The UWK 11R has 1700W of power and weighs only 2.5kg. It is a ‘muscle-machine’ that enables use of high torque and can be combined with various grinding and finishing discs including Suhner’s Magic grinding discs. It also provides more than the recommended power for optimal use of 3M® Cubitron fibre discs. Other key features of the new […]

Man,And,Woman,Hand,Holding,Jigsaw,Puzzles,,Business,Matching,Concept

Shift to shared office and distribution centre model increases demand for security

A shift in commercial real estate mentality is increasing the demand for security, to separate previously unconsidered areas, thereby ensuring the protection of all staff, visitors, equipment, and product. With e-commerce continuing to grow, and as more workplaces offer a flexible work from home balance, companies are beginning to combine their offices with their distribution centres, to add convenience and cost-savings to their operations. “These combined workspaces are often closer to employees’ homes, and companies can lease a single building, instead of having to lease two separate ones – it makes good economic and social sense,” says Boon Edam Australia Managing Director, Michael Fisher. “However, with this combination, comes risk. There’s a new need to separate people from product, or customers from a warehouse space. Having the right security in place will be essential to companies seeking smooth and safe operations at these combined facilities,” he said. Boon Edam Australia is a local leader in elegant architectural entrances and integrated security solutions for leading companies, including Fortune 500 companies in 27 countries where its reputation for quality and service is valued highly by architects and security specifiers. It is backed by the family-owned 150-year old Royal Boon Edam group. In addition to having one of the world’s most extensive ranges of revolving doors and security entrances integrated from one source, the other major consideration is appearance, says Fisher. “These combined facilities are often major brands and household names. They are seeking not only reliable and functional security solutions, but technologies that match the elegance and style of their brand,” he says. An elegant and secure solution A solution that seamlessly integrates elegance with security is Boon Edam’s Speedlane Lifeline range of speed gates. The Lifeline range has been a global market leader for years, and offers one of the slimmest […]

First Person View of Professional Freelancer Working on Green Mo

Configuring and programming igus linear robots – as easy as playing PlayStation

Gamification approach and additional features make online configurator for low-cost linear robots even more intuitive. With the help of the game engine Unity, motion plastics specialist igus has given its online configurator for low-cost linear robots a facelift, making its operation even more efficient. Now, users can configure an individual linear robot ready for connection faster and easier – in just five minutes. With the help of the online tools, any automation solution can be programmed and tested directly in the selected working area and also load CAD data and a suitable drawing. Even small and medium-sized companies can immerse themselves without a barrier in the world of automation – without the know-how of specialists and CAD software. Increase efficiency, reduce errors and lower costs: many companies are recognising the benefits of process automation. But choosing the right robot can be time-consuming – and time is money. Last year, igus developed an online configurator to make it easier getting started with automation. With just a few clicks, customers can easily configure ready-to-connect low-cost linear robots based on sliding drylin linear guides. Linear robots are available without control system, and with control system and software. “Since the launch of the configurator, we received a lot of positive feedback on the gamification approach and intuitive usability,” says Alexander Mühlens, head of the Automation Technology and Robotics division at igus. “Nevertheless, we asked ourselves: Can we continue to improve operation with this feedback? The answer was a resounding yes. As a result, we have further optimised the configurator and added new functions.” Configure individual robots — even easier thanks to the gaming platform For the new design of the configurator, the igus developers used Unity – a platform used in the development of games for PC and game consoles. Operation of the configurator […]

Kemppi releases new MasterMig range

Leading international welding equipment manufacturer, Kemppi, has released its new MIG/MAG MasterMig welding machine models 353 and 355. The 358 model is scheduled for release later this year. Designed in conjunction with professional welders, the new MasterMig range delivers a range of features to help enhance industrial welding productivity and quality. Faster set-up for greater productivity The new, compact and powerful Kemppi MasterMig range comes with Weld Assist as standard. This feature lets users set-up welding parameters quickly and easily to save time and improve productivity levels. By simply selecting the joint type, welding position and material thickness, users are ready to weld. Equipped with memory channels, the MasterMig range also lets users save chosen parameters for fast retrieval. The ability to save customised settings means welders do not have to go through an initial setup for every job. At the turn of a knob, they can highlight the desired setting and proceed to weld. Highly convenient, this feature saves precious time, while helping to increase productivity. Better Arc Performance Delivers More Productivity For greater welding productivity and control, the MasterMig 355 and 358 models can switch on the new MAX arc performance welding processes. MAX Cool, MAX Position and MAX Speed are new Kemppi welding processes that offer solutions for challenging steel, stainless steel and aluminum welding applications by increasing productivity, minimising spatter and speeding up welding without compromising quality. The MAX software options easily integrate with the MasterMig 355 and 358 models. A choice of models Suitable for use on site or at the workshop, the MasterMig range delivers real choice. It includes the 353, 355 and 358 models in the compact MIG welding category. These are available as manual, synergic (Auto), and pulse (Auto Pulse) welding options. Users can also choose to weld with gas-cooled guns or […]

«‹ 2 3 4 5 ›»

News Ticker

Products